HP25 Assembly Formats
Typical options include:
- 3 mm wire rope with soft eye
- 3 mm wire rope with open end
- Clevis to suit M6 threaded bar
- Couplers, nuts and washers
- Flat or domed bearing plates
- Eye nuts
- Pre-assembled specialised kits
A successful ground anchoring system requires more than selecting an anchor head.
The anchor, tendon, termination, load-distribution components and structural connection must work together as a complete system. The system must also be capable of being installed and tested using equipment suited to the project conditions.
Depending on the agreed scope, AR+R can assist with:
This reflects AR+R’s role as the Australian manufacturer, technical partner and project-delivery organisation rather than solely a product reseller.
Installation of Hulk HG Anchors using a hand operated hydraulic jackhammer
A HULK Earth Anchor installation may include the following components.
The percussion-driven tipping-plate component installed below ground.
The load-transfer component connecting the anchor head to the supported structure or asset. Tendon formats may include wire rope, chain, threaded bar or CTB rod.
Protection requirements may vary according to the material, exposure conditions and intended design life.
The component or arrangement used to terminate the tendon and transfer load into the connection.
A bearing plate, washer or other component used to distribute load at the surface or structural connection.
The detail connecting the anchor assembly to the asset, foundation, structure or reinforcement system.
Reusable Smasher Rods or drive steels are used for installation, followed by suitable equipment for activation and proof testing.
Hulk Earth Anchors installed for a bridge abutment repair. Installation with an excavator with a mounted hydraulic breaker.
HULK Earth Anchors can be supplied with a variety of tendon and connection formats.
These are general assembly formats rather than project-selection instructions. The final configuration must be considered against the required load, ground conditions, depth, installation angle, corrosion exposure, design life, connection and testing requirements.
Typical options include:
Typical options include:
Typical H-range options include:
Typical HG-range options include:
HULK Earth Anchors can be installed using light, medium or heavy equipment selected to suit the anchor model, required depth, ground conditions, installation angle, site access and available plant. Reusable HULK Smasher Rods and Power Smasher Rods transfer the driving energy from the selected installation equipment to the anchor head. HULK Smasher Rods are manufactured from impact-resistant steels and are available in different lengths, diameters and shank configurations to suit a range of installation equipment.
The appropriate combination of anchor, Smasher Rod and installation equipment should be selected according to:
Installation equipment must be matched to the relevant HULK Earth Anchor range and proposed installation method.
Smaller HULK Earth Anchors may be installed using a Hand Smasher Rod and suitable manual impact equipment. This method is generally suited to light-duty installations and locations where powered equipment is unnecessary or access is restricted.
Fixed-length Power Smasher Rods are used with compatible handheld percussive equipment where greater installation energy is required.
Depending on the equipment connection and installation requirements, extendable Power Smasher Rods may also be used with handheld powered equipment to achieve greater installation depths.
Larger anchors, deeper installations or more demanding ground conditions may require excavator-mounted or other suitable powered equipment.
Extendable Power Smasher Rods allow additional rod sections to be added as the anchor is driven, making them suitable for deeper installations using excavator-mounted equipment.
After the anchor has been driven and the Smasher Rod or drive steel has been removed, the anchor must be activated by applying a tensile load through the tendon.
This process rotates the anchor head from its driven orientation into its load-resisting position within the ground.
Where a nominated proof-test load applies, suitable testing equipment can be used to activate and test the anchor during the same operation.
Smaller anchors, such as the HULK HP25, may be activated using a manual pull or by using the drive rod as a lever or handle.
Larger anchors may also be activated using suitable mechanical equipment, such as a high-lift jack or excavator. Where proof testing is required, a calibrated load cell or other appropriate load-measuring equipment must be incorporated into the pulling arrangement.
The PT45 is a manually operated hydraulic testing jack designed to activate and proof test HULK Earth Anchors to loads of up to 45kN.
It provides a controlled and measurable method of applying load and is suitable for HULK anchors up to the H110 , subject to the required project test load and assembly configuration.
The PT150 is a powered hydraulic testing ram designed for heavier HULK Earth Anchor installations and proof-test loads of up to 150kN.
It can be used across the HULK range up to the HG320 , subject to the required test load, tendon connection and installation arrangement.
Ground conditions can vary across a site, even where geotechnical information is available.
Proof testing allows the response of the installed anchor system to be assessed in its actual location. Depending on the project requirements, testing may help:
The required proof-test load and acceptance criteria should be established by the project engineer or relevant specification where applicable.
AR+R can undertake HULK Earth Anchor installation as a specialist contracting service.
A contract installation scope may include:
Installation planning can also address restricted access, steep terrain, limited work windows, existing structures and other project constraints.
Where installation is undertaken by the client, contractor or distributor, AR+R may provide supervision or training appropriate to the agreed scope.
Support may cover:
Training and supervision do not replace project-specific engineering, site safety requirements or the contractor’s responsibility for the work.
Depending on the project and agreed scope, AR+R can assist with:
Slope stabilisation project, installation of Hulk HG anchors with an excavator with mounted hydraulic hammer.
Yes. AR+R can supply anchor heads, tendons, terminations, connection hardware and pre-assembled or project-specific systems.
Depending on the application and project requirements, installation may be undertaken by a contractor using appropriate equipment. If required AR+R can also provide installation, supervision or training.
Testing requirements depend on the project specification and application. Where verification to a nominated load is required, the anchor can be activated and proof tested using appropriate equipment.
AR+R manufactures and supplies HULK Smasher Rods and can assist with installation and proof-testing equipment requirements.
Contact AR+R for assistance with product supply, anchor assemblies, installation equipment, contract installation, proof testing, supervision or training.
Call: 1300 692 626
International: +61 2 4372 1422